(See, tmctl read me(ENG).txt conrained in the above zip file for further details). When Using a GPIB Interface An instrument from YOKOGAWA equipped with an IEEE Standard 488.2 compliant GPIB interface. Communications can be carried out with non-YOKOGAWA instruments, but some functions may not be available.
When Using an RS232 Interface An instrument equipped with an RS232 interface supporting the following settings. Baud rate: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Data bit length, parity, and stop bit length combination: 8 bits, no parity, 1 stop bit 7 bits, even, 1 stop bit 7 bits, odd, 1 stop bit Handshaking: NO-NO (no handshaking) XON-XON (software handshaking) CTS-RTS (hardware handshaking) Terminator: LF, CR+LF Communications can be performed with non-YOKOGAWA instruments, but some functions may not be available.
(See, tmctl read me(ENG).txt conrained in the above zip file for further details). When Using a GPIB Interface An instrument from YOKOGAWA equipped with an IEEE Standard 488.2 compliant GPIB interface. Communications can be carried out with non-YOKOGAWA instruments, but some functions may not be available. When Using an RS232 Interface An instrument equipped with an RS232 interface supporting the following settings. Baud rate: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Data bit length, parity, and stop bit length combination: 8 bits, no parity, 1 stop bit 7 bits, even, 1 stop bit 7 bits, odd, 1 stop bit Handshaking: NO-NO (no handshaking) XON-XON (software handshaking) CTS-RTS (hardware handshaking) Terminator: LF, CR+LF Communications can be performed with non-YOKOGAWA instruments, but some functions may not be available.
System Requirements PCA PC with a 80486DX2 CPU or later (Pentium or later recommended), and 8 MB or more of memory. System Requirements Personal Computer CPU Premium4 1.5 GHz or higher (recommended) Memory 1 GB or more (recommended) Hard Disk 500 MB or more of free space OS Microsoft Windows XP, Windows Vista, or Windows 7.(All English versions) Communication Port GP-IB NI (National Instruments) AT-GPIB, PCI-GPIB, PCI-GPIB+, PCMCIA-GPIB, PCMCIA-GPIB+, or PCIe-GPIB with driver NI-488.2 version 1.60 or later (however, version 2.3 is not supported).
RS-232 An available COM port on the PC Ethernet 10BASE-T or 100BASE-TX compatible Ethernet port USB A USB Rev. 1.1 or later USB port Display, Printer, and Mouse Screen Resolution 1024 × 768 pixels or higher Applicable Operating Systems Must be compatible with the operating systems listed above. Connecting the WT Series Instrument to a PC GP-IB Interface to prevent electric shock, turn the power to the instrument OFF when connecting it to the PC. Connect a GP-IB cable from the GP-IB connector on the rear panel of the WT series instrument to the corresponding connector on the PC. Setting the Address Set the GP-IB address according to the procedure given in the user's manual that came with the WT series instrument. For details about the GP-IB interface, refer to the information about the communications functions included in the user's manual. RS-232C Interface To prevent electric shock, turn the power to the PC OFF when connecting the instrument to it.
Connect an RS-232 cable from the RS-232 connector on the rear panel of the WT series instrument to the serial port of the PC. Parameter settings Follow the procedure given in the user's manual of the WT series instrument to enter the following parameter settings. (Normally, operation can begin using the factory default settings.) Handshaking: select a method from 0 to 7. Data format: select a format from 0 to 3.
Baud rate: select 75, 150, 300, 600, 1200, 2400, 4800, or 9600. Terminator: select CR+LF, CR, or LF.
For details about the RS-232 interface, refer to the user's manual that came with the WT series instrument. Installation All four downloadable program files are self-extracting executables which, when double-clicked, create new files and folders on your hard drive.
Two of those four programs require no further installation, but the other two create an additional Setup.exe file which must be executed to complete the installation. Turn ON the PC and start Windows. Create a new folder on your hard disk with a name of your choice, and download the free software into the folder. Double-click the file necessary for your WT series model, then click OK in the dialog box. A new folder, YOKOGAWA, will be created on drive C and files will be extracted to it. Specify any changes you wish to make to the destination folder.
Technics Dl-1200
When the extraction is finished, check to see if the program executable file was created. If so, installation is complete. If the Setup.exe file (rather than executable files) was created you will need to perform a few more steps to complete the installation. Double-click the Setup.exe file, and follow the on-screen instructions.
Creating Icons for the WT Free Software After the program has been fully installed, you can use Explorer or the My Computer browser to create a shortcut to the program. Locate the executable file, right-click its icon, and select Create Shortcut from the shortcut menu. Weatherby vanguard rifles serial numbers. Running/Exiting the Software.
Running the software Double-click the program executable file or its shortcut to run the software. Or, if the program was installed using a Setup.exe file, select Start Programs Yokogawa, then the name of the program you wish to run. Exiting the software Select File Exit, or Close the program window.